Skip to main content


Strong tube clamps (white or black) made from plastic, that can be employed as boathook holders, door handle clamps or bracket für the tiller. Up to size 55 x 22 mm the clamps are fixed with one central screw, the larger sizes are fixed with two side screws.

Material: UV stabilised plastic SANTOPRENE.
Shipping in pairs as a set.
Colour: black or white.

Last seen products

More articles from this category

Boathook holder for lashing at the shrouds
Stainless steel bracket for attachment with tape, cable ties or whipping at the shrouds.

€20.50 *
Boathook holder basket for lashing at the shrouds
Stainless steel bracket for attachment with tape, cable ties or whipping at the shrouds.

€34.90 *
Boathook holder for screwing at the shrouds
Stainless steel bracket for mounting at the shrouds. Attachment with welded stainless steel clamp and screw M4. Maximum wire thickness 7 mm.

€26.90 *
Boathook holder basket for screwing at the shrouds
Stainless steel bracket for mounting at the shrouds. Attachment with welded stainless steel clamp and screw M4. Maximum wire thickness 7 mm.

€45.90 *
Plastic spring clip
Made from plastic suitable for boat hooks, spinnaker poles as well as tiller extension.Colour: anthracite.

From €3.40 *
Spring clip, plastic
Solid spring clip made from black plastic with two screw holes for mounting.

From €3.65 *
Boathook holder / spring clip
Strong tube clamps (white or black) made from plastic, that can be employed as boathook holders, door handle clamps or bracket für the tiller. Up to size 55 x 22 mm the clamps are fixed with one central screw, the larger sizes are fixed with two side screws.Material: UV stabilised plastic SANTOPRENE.Shipping in pairs as a set.Colour: black or white.

From €3.10 *
Folding boathook holder
Sturdy fold out holder made from black plastic with a spring lock-in position, the base plate is made from stainless steel.

€19.90 *
Bronze rudder gear SPARTAN
Light, but very robust folding-tiller fitting, made from heavy duty cast bronze, tumbled matt finish.Stainless-steel bolting.The tiller is screwed or bolted between the cheeks and can be folded into a perpendicular position.Available for UNC rudder shafts of imperial diameters, with keyway and threaded clamp.A quality product from SPARTAN, the American manufacturer of traditional equipment.

€399.00 *
Bronze rudder gear SPARTAN heavy
Heavy and very robust folding-tiller fitting, made from heavy duty cast bronze, tumbled matt finish. Stainless-steel bolting. The tiller is screwed or bolted between the cheeks and can be folded into a perpendicular position. Available for UNC rudder shafts of imperial diameters, with keyway and threaded clamp. A quality product from SPARTAN, the American manufacturer of traditional equipment.

From €399.00 *
Tiller fitting DAVEY
Rudder head for folding tiller.Beautiful, heavy tiller fitting , made from hand-polished cast bronze.Measurements:length L = 200 mmwidth exterior = 45 mmwidth inner = 34 mmweight 1050 gFor 10 mm diameter bolts, single threaded M10.The matching adaptor for rudder shaft must be made separately.

€225.00 *
Stainless tiller fitting HOLT ALLEN
Cleanly worked fitting of stainless steel, with which tiller extensions can be attached on the tiller so they will pivot and turn. At 13 mm wide, the tiller joint is so thin that it can be used on wood, aluminum or carbon fiber tiller extensions. Dimensions:Base plate 50 x 20 mm.

€32.00 *
Rubber joint for tiller extension OPTIMIST
OPTIMIST rubber joint for tiller extension, with DYNEEMA-core.

€9.00 *
Rubber joint for tiller extension OPTIPARTS
OPTIMIST rubber joint for tiller extension, with DYNEEMA-core.

€16.00 *
Auto Pilot Tiller Fitting
The strong bracket made of cast bronze with polished surface enables optimal, horizontal mounting of the tiller autopilot when the tiller of the boat is lower or higher than the fixed end of the autopilot tiller drive. Made in England by DAVEY. Supplied without pin for the inlet socket on the autopilot tiller drive. A hole for inserting the pin corresponding to the autopilot model is provided, Ø 6.5 mm.

€79.50 *
Boathook holder
Teak chock 70 x 30 x 40 mm with integrated rubber ring for securing boat hooks.Comes in pairs with 10 mm bungs.

€41.95 *
Stainless steel holder / bracket
Stainless steel holder for life rings.Also well suited for hanging rope, fenders, tools, etc.

From €8.50 *
Boathook holder
Spring-loaded cleat for holding boathooks, paddles, pipe, etc. Made from stainless steel spring plate, 1.3 mm thick.

From €5.90 *
Bronze rope holder
Made from strong matte bronze for the hanging-up of rope, fenders, boat hooks, oars, etc.Delivery without the pictured cordage.

€74.00 *
Bronze boathook holder
Strong bronze ring, surface tumbled matt finish.For fitting to the shroud.Maximum thickness of shroud 10 mm, ring 6 mm.

€69.90 *