PHILIPPI battery-tank monitor BTM2

Art. No.	description	voltage (V)	L (mm)	B (mm)	H (mm)	Price (unit)	Delivery time	Note list	Buy

Downloads

Easy-to-use battery tank monitor with touch colour display.

Battery monitoring: current voltage, charge or discharge current, remaining time, temperature and state of charge of the consumer battery (optional shunt required). Historical values on the number of charging cycles, deep discharges and average depth of discharge provide an overview of the battery's use. The voltage of two other batteries can be monitored.

The optional digital battery shunt SHE348 is installed in the negative lead of the consumer battery. With the SHP348 shunt, further current measurement for charging sources (solar) is possible. Both shunts are supplied with power via the voltage measurement line of the connected consumer battery. The shunts are suitable for continuous charging or discharging currents up to 300 A and battery capacities up to 1000 Ah.

Tank monitoring: The fill levels of up to four tanks can be monitored. The threshold values for alarms and the tank geometry can be configured. Suitable for tank sensors TGT/TGW, UTV, TDS/TDN or input signal ranges 10-180 Ohm/240-33 Ohm/0-5 V/0-10 V/4-20 mA.

Chargers of the PHILIPPI ACE series with ACE-LIN interface can be integrated and thus values for the charging process can be displayed.

The integrated NMEA2000 interface allows the battery and tank data to be integrated into the on-board network (optional N2K cable 4378-015 required).

Operating voltage 12-48V DC.

Questions about the product?

Accessories

Tank sensor TGT for fuel or waste water TUROTEST

Mechanical tank sensor TGT for diesel and wastewater tanks. Works with the tank gauges of the TUROTEST instrument series. The stainless steel tube sensors are a German product.High resolution (a switching point every 17mm).5 (empty) to 180 (full) ohms.Thread 1.1/4".Comes with a plastic flange and gasket.Lengths of up to 800mm are available on request.

From €115.90 *

Details

PHILIPPI TGW tank sensor for water tanks

Mechanical tank sensor TGW for fresh water.For gauges of TUROTEST series. The stainless steel tube sensors are made in Germany.High resolution (a switch point every 17mm), thread 1 1/4".5 (empty) to 180 (full) ohms.Comes with mounting flange and gasket.

From €122.90 *

Details

Ultrasonic tanksensor TUROTEST UTV

Non-contact tank sensor for ultrasonic tank gauge. For water, diesel, grey water or waste tanks. The use of ultrasonic technology means that there are no moving parts required in the tank.Works perfectly in plastic tanks. Not suitable for metal tanks.The sender is mounted in top of the tank (bolt circle diameter of 53 mm per SAE with 5 holes) and can even replace a mechanic sensor (with appropiate gauge). Sensors are available for tank depths up to 800 mm.The distance washer has a height of 25 mm; the height can be varied by using several washers.Voltage 10-30 volts,Power draw 50 mA,Output signal 0.5 - 2.5 volts.The matching gauges please find listed at "Suitable items" below.

From €109.00 *

Details

PHILIPPI flow sensor DFS24

Flow sensor for fresh water for connection to a digital tank monitor BTM(2), VTM(2).Number of pulses: 1000 pulses /L.Dimensions : L 110 x W 23 x H 57 mm

€119.00 *

Details

Last seen products

More articles from this category

Battery monitor BMV VICTRON

This battery-"tank gauge" surveys the charging condition of one battery bank and calculates the remaining capacity (taking in account the battery condition and temperature). Displayed are: - battery voltage,- charging current,- consumed Amp hrs,- remaining battery capacity,- current consumption,- charge status,- programmable visual and audible alarms,- programmable relays to start a generator in case of a voltage drop, for instanceEasy installation: only the 500 A shunt is to be installed in the battery cable (as close to the battery as possible) and to be connected to the display with the included RJ12 cable (length 10m).The unit is programmed using the quick installation menu.BMV-700: monitor for one battery. Simple calibration with the quick installation menu.BMV-702: like BMV-700, but with the possibility to show the voltage of a second battery.BMV-712: SMART version. An integrated Bluetooth module enables the programming, the readout and the interconnectedness as well as the definition of alarms by smartphone or tablet with the VICTR ON Bluetooth App. It has the same functions as BMV-702.The display comes complete with 500A shunt and RJ22 cable (length 10m). High current measurement resolution: 10 mA.Low current consumption: 2,9Ah per month at 12 V (with constant use).Wide input voltage range: 9,5 - 95 V. Mounting either directly (D: 63mm) or using the supplied cover (69 x 69mm).

From €139.00 *

Details

PHILIPPI battery-tank monitor BTM2

Easy-to-use battery tank monitor with touch colour display.Battery monitoring: current voltage, charge or discharge current, remaining time, temperature and state of charge of the consumer battery (optional shunt required). Historical values on the number of charging cycles, deep discharges and average depth of discharge provide an overview of the battery's use. The voltage of two other batteries can be monitored.The optional digital battery shunt SHE348 is installed in the negative lead of the consumer battery. With the SHP348 shunt, further current measurement for charging sources (solar) is possible. Both shunts are supplied with power via the voltage measurement line of the connected consumer battery. The shunts are suitable for continuous charging or discharging currents up to 300 A and battery capacities up to 1000 Ah.Tank monitoring: The fill levels of up to four tanks can be monitored. The threshold values for alarms and the tank geometry can be configured. Suitable for tank sensors TGT/TGW, UTV, TDS/TDN or input signal ranges 10-180 Ohm/240-33 Ohm/0-5 V/0-10 V/4-20 mA.Chargers of the PHILIPPI ACE series with ACE-LIN interface can be integrated and thus values for the charging process can be displayed.The integrated NMEA2000 interface allows the battery and tank data to be integrated into the on-board network (optional N2K cable 4378-015 required).Operating voltage 12-48V DC.

From €285.00 *

Details

Voltmeter PHILIPPI

To make the panels complete, there is the voltmeter with switch over for service- und starter battery available.

€89.00 *

Details

Battery management controller STERLING PMP1

This Power Management Panel (STERLING PMP1) is a combined instrument including 4 voltmeters, 4 amp meters and one amp hour counter: The amp hours of one battery bank (generally the main domestic bank) are measured and displayed like tank contents (charging current minus consumption).At three other measuring points (which require additional shunts which must be ordered separately) you may measure current (amps) and voltage (V). Indicators: Ampere hours (1x), Current (amps) (4x), Voltage (V) (4x). LCD display.For 9 - 33 V systems.Comes with 1 shunt for one measuring point. Optional accessoires: Further shunts for additional measuring points.

From €324.00 *

Details

Mon - Fri:	09 am - 06 pm
Sat:	09 am - 01 pm