Gaiter-Kit for WHALE/HENDERSON deckplates

Impeller for impellerpump MARCO UP1

Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.

€32.90 *

Details

Service kit for WHLALE GULPER 220/320

Contents of service kit AK1550:MembraneValve flapVentMounting screws.Clampingring - kit AS1562 consists of clamping ring and screws.The service kit "pump head" (AK2050) holds the spare parts for the pump head (please check "Downloads & Information").

From €53.00 *

Details

Service kit for WHALE GULPER waste pump

Accessory for waste pump WHALE GULPER.

€64.00 *

Details

Bilge water filter (oil strainer) WAVESTREAM

The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.

From €179.00 *

Details

Filter cartridge for WAVESTREAM bilgewater filters

Accessory for bilge water filter WAVESTREAM.

From €39.90 *

Details

Spare parts for bilge pump PLASTIMO 12760

Accessory for PLASTIMO bilge pump type 12760 (our Art-No. 1768-025).

From €32.90 *

Details

Spare parts for bilge pump PLASTIMO 11722 / 11723

Accessory for PLASTIMO bilge pump art-no. 1768-038 and 1768-039.

From €17.90 *

Details

Outlet elbows for diaphragm pump PLASTIMO 11722

Outlet elbows for the diaphragm pump PLASTIMO model 11722.They are screwed and fitted with an O-ring for perfect water tightness and added safety (quick release facility). For a tube diameter of 38mm.

€17.90 *

Details

JABSCO Impeller

Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

From €37.00 *

Details

Tool for removing impellers JABSCO

An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *

Details

Grease for impellers JABSCO

Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

€3.90 *

Details

Impeller-kit JABSCO 6303-0003K

Spare impeller for JABSCO pumps.

From €34.90 *

Details

Impeller for impellerpump MARCO UP1-J

Impeller IMP2 of special nitril rubber. Original spare part for UP1-J and UP1-JR MARCO pumps.Dimensions hight x Ø: 22 x 40.5 mm.Bore Ø: 8 mm.

€32.90 *

Details

JOHNSON impellers

Original long-lived SPX/JOHNSON brand neoprene and Nitrile rubber impeller. Usually the impellers come with matching cover gaskets of paper. To see the matching image for the impeller, simply click on the part number in the table below.Impellers made of oil-resistant nitrile rubber have a high resistance to oils, greases and hydrocarbons, they have good aging properties and low abrasion. Nitrile impellers are used, for example, for bilge pumps when the water is heavily contaminated by oil or diesel.MC97/EPDM and neoprene impellers are used for engine cooling and fresh or salt water pumping. Neoprene is the most commonly used material and is suitable wherever very small amounts of oil or diesel fuel are present.

From €27.90 *

Details

Impeller

The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.

From €18.90 *

Details

Vacuum switch for impeller pumps

For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.

€59.90 *

Details

Spare parts for WHALE GUSHER 10

We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.

From €72.90 *

Details

Spare handle for WHALE GUSHER & TITAN bilge pumps

Spare handle for WHALE GUSHER 10 and WHALE TITAN bilge pump.Inox tube with black plasic knob.

€62.90 *

Details

Deck/bulkhead plate for WHALE-pumps

Deckplate for WHALEpumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.Article-no. 1860-110 (DP8904) fits for Gusher 10, Urchin, Titan.

€49.90 *

Details

Gaiter-Kit for WHALE/HENDERSON deckplates

Service kit for WHALE/HENDERSON deckplates suitable for underdeck models Gusher 30 and 10, Titan, Urchin, Mk5The kit includes a gaiter (diameter 108mm) and an O-ring.

€36.90 *

Details

Mon - Fri:	09 am - 06 pm
Sat:	09 am - 01 pm