Go to homepage
€0.00*
Jobs
Catalogue
Quick order


Downloads

With integrated check valve for hoses of 25 mm and 38 mm.
With sieve on the outboard side.

Questions about the product?

Similar products

Multiflex hose PVC
Multiflex hose PVC
Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).

From €4.90 *
Details
Electric diaphragm pump WHALE GULPER 320
Electric diaphragm pump WHALE GULPER 320
WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.

From €259.00 *
Details
Bilge strainer WHALE
Bilge strainer WHALE
With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the onboard side.

€35.90 *
Details
Bilge strainer WHALE
Bilge strainer WHALE
Bilge strainer with check valve, easy to clean.With 19 mm hose connector.The connector can be mounted in three directions: standing, horizontal, sideways.

€64.90 *
Details
MARCO float switch AS3
MARCO float switch AS3
Robust bilge switch with high switching capacity for powerful pumps.  Very reliable switching due to a spring-loaded microswitch. Suitable for 12 volts and 24 volts. The switching capacity is maximum 168 VA (14A at 12V, 7A at 24V).The switch turns the pump on at a water level of 51mm and off at a water level of 19mm.

€36.50 *
Details
WHALE field sensor bilge switches BE9003 / BE9006
WHALE field sensor bilge switches BE9003 / BE9006
This electronic level switch does not require any mechanics or moving parts. Two field sensors ensure functional switching on and off of the connected pump. The switch turns on at 51 mm water level and turns off at 13 mm water level. The automatic sensor type BE9006 switches with an automatic 30 seconds switch-off delay. This delay allows water to be pumped out even below the switching level of 13 mm. The test function can be used to check the function of the pump after installation.Voltage: 12 V / 24 V.Max. switch current: 20 A.Residual current: 0,008 A.

From €69.00 *
Details
Thru-hull hose fitting polished or chromed
Thru-hull hose fitting polished or chromed
Through-hull with attached hose nozzle. Made of brass (seawater resistant brass, depending on manufacturer CW602N - CuZn36Pb2AS or CW625N - CuZn35Pb1,5AlAs).Comes in rolled brass or with a chromed finish.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €11.00 *
Details
Switch panel for bilge pump SEAWORLD
Switch panel for bilge pump SEAWORLD
Switch panel for automatic bilge pump. With sound and light alarm when pump is running automtically.With toggle switch, positions: "automatic/off/manual". With control lights and fuse 16 A/12 V. For 12 volt systems.

€25.90 *
Details

Last seen products

More articles from this category

Bilge strainer WHALE
Bilge strainer WHALE
With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the onboard side.

€35.90 *
Details
Bilge strainer WHALE
Bilge strainer WHALE
With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the outboard side.

€35.90 *
Details
Bilge strainer WHALE
Bilge strainer WHALE
Bilge strainer with check valve, easy to clean.With 19 mm hose connector.The connector can be mounted in three directions: standing, horizontal, sideways.

€64.90 *
Details
Check valve WHALE
Check valve WHALE
Made of glass fibre reinforced PP plastic with high-quality nitrile lip valve. Suitable for bilge water systems or hand and electric bilge pumps.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €29.90 *
Details
Non return valve WHALE
Non return valve WHALE
Made of glass fibre reinforced PP plastic with high-quality nitrile lip valve. Suitable for bilge water systems or hand and electric bilge pumps.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

€35.90 *
Details
Check valve WHALE
Check valve WHALE
Small, spring-loaded ball check valve especially for drinking water hand pumps.The valves are installed directly in the suction hose (13 mm), as close as possible to the tank.It makes sense to install the valve if there is a problem with backflow into the fresh water tank and water has to be pumped for a long time until it flows out of the tap.Cannot be used in pressurised water and bilge pump systems.

€15.90 *
Details
Check valve PLASTIMO
Check valve PLASTIMO
Plastic non-return valve with oil-proof nitrile rubber valve. Suitable for bilge water systems or hand and electric bilge pumps.The valve housing is easy to open (for maintenance). In narrow spaces, the straight gland can be replaced with an angled one.Entire length 185mm.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €6.90 *
Details
Non return valve JABSCO
Non return valve JABSCO
Non return valve made from plastic by the global market leader JABSCO with hose connectors on both ends and a check valve made from Nitrile rubber.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €35.90 *
Details
Brass bilge water strainer
Brass bilge water strainer
Special brass, with non-return valve, strainer can be unscrewed.

From €21.00 *
Details
Brass check valve
Brass check valve
Brass check valve, spring operated.To be fitted in the tube to prevent reflux of water.With inner threads on both sides. Strong body of brass, valve cage of nylon, spring of A2 stainless steel, seal of nitrile rubber.The valve works in any installation situation.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €10.90 *
Details
Non return valve from TRUDESIGN
Non return valve from TRUDESIGN
Non return valve made from glass fibre reinforced composite plastic fitted on both ends with a hose connector.The valve plug is made from nylon with a stainless steel spring, the length is 85 mm.Suitable for fresh water pipe systems. TRUDESIGN is the world leader in fittings made from composite materials. From its founding in 1974 the fittings are manufactured in New Zealand. Every TRUDESIGN part is made from high tensile composite GRP, a glass fibre reinforced Polyamide (6). The advantages are a high rigidity, temperature-resistance -40° to 80° C, resistant to oil and chemicals, of low weight, absolutely corrosion-resistant, electrically non-conductive and therefore especially suited for ship building materials which are galvanically sensitive like aluminium and steel.Every TRUDESIGN fitting has a tapered Whitworth pipe thread BSP (British Standard Pipe Thread) according to ISO 228-1, it is therefore fully convertible with fittings from brass, bronze or stainless steel. The shuttle valves and through hulls are approved and IMCI certificated after ISO 9093-2 (sea cocks and through hulls for pleasure vessels).

From €13.90 *
Details
Brass screw-in sieve filter with stainless steel sieve
Brass screw-in sieve filter with stainless steel sieve
Screw-in sieve filter consisting of a brass body with an inch external thread and a sieve made of A2 stainless steel.Good for protecting the pump from coarse impurities when drawing in outside water or bilge water. Depending on the intended use, we recommend screwing the suction basket into a standpipe, a pipe-to-hose fitting or a non-return valve. See the example photos with corresponding accessories (not included in the scope of delivery).Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €6.90 *
Details