RYLARD VG66 Premium classic high gloss varnish

BIOPIN BOOTSLACK is a traditional, high-gloss wood oil clear varnish with good elasticity and excellent flow. It is weatherproof, seawater-resistant, and abrasion-resistant. The product has good penetration and adhesion properties and offers long-term protection against UV radiation. Application Apply on a dry, dust- and grease-free surface using a brush, roller, or spray device at temperatures above 8 °C. For new wood, a primer with BIOPIN BOOTSLACK (diluted 10–20%) or BIOPIN BOAT OIL (Art.No. 2631-140) is recommended. Then apply one to three undiluted coats, sanding between coats. For old coatings in poor condition, complete removal may be necessary. For old coatings in good condition, sanding and 1–2 new coats are sufficient. Do not crumple contaminated cloths due to risk of spontaneous ignition; instead, allow them to dry spread out.Technical DataApplication area: Clear varnish for wood indoors and outdoors, especially for boats and damp areasSubstrate: Clean, dry, dust- and grease-free; also suitable for wood-based materialsPrimer: BIOPIN BOOTSLACK diluted or BIOPIN BOAT OILCoverage: approx. 12 m²/l Thinner: BIOPIN THINNER or turpentine oilApplication method: Brush, roller, spray device (professional use)Drying times (at 20 °C): Dust-dry: 4–6 hrs, recoatable: after 8–12 hrs (depending on temperature fluctuations)Further information on application can be found in the technical data sheet under 'Downloads'.

EPIFANES AQUA MARINE SATIN VARNISH is a water-based, satin-finish interior clear varnish based on polyurethane/acrylic resin. It is characterized by high scratch resistance, fast drying, and high resistance to alcohol and common household cleaners. Suitable for all types of wood in interior areas and results in a clear, even surface after drying. The product is VOC-reduced and low-odor, ideal for interiors with high demands on application and environmental compatibility.Application: For bare wood, a multi-layer build-up with EPIFANES CLEAR BOAT VARNISH (Art. No. 2050-001) is recommended, which is then finished with two coats of EPIFANES AQUA MARINE SATIN VARNISH. Alternatively, the varnish can be applied directly to clean and sanded old coatings. Application is done with a brush or spray gun at temperatures above 8 °C and max. 85% relative humidity. An intermediate sanding with P220 is required between coats. Thinning with water up to a maximum of 15% is possible. Note: The varnish appears milky during application but dries clear.Technical DataApplication area: Satin-finish clear varnish for all wooden surfaces indoorsSubstrate: Clean, dry, grease-free; suitable for all types of woodPrimer: Multi-layer base with EPIFANES CLEAR BOAT VARNISH (Art. No. 2050-001) recommendedCoverage: approx. 12 m²/l at 25 µm dry film thicknessThinning: Water, 0–15%Application method: Brush or spray gun (1.5–1.8 mm, 2–3 bar)Drying times (at 20 °C, 65% r.h.): Dust-dry: 1 hr, sandable: 4 hrs, recoatable: 6 hrsFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

The proven classic among one-component clear coats: EPIFANES boat varnish . High gloss, easy to apply and very durable. This air-drying varnish based on wood oil, phenolic resin and alkyd resin is suitable for use on solid wood and plywood indoors and outdoors above the waterline. The varnish forms a transparent amber-colored, gloss-stable protective film with very good weather and UV resistance. Its high elasticity prevents cracking on working wood. Suitable for coating raw wood (mahogany, meranti, Oregon pine) and plywood above the waterline&nbsp

EPIFANES POLY-URETHANE DD-Yacht Varnish satin gloss is a scratch-resistant two-component clear varnish based on saturated polyester resins and isocyanate with integrated UV filter. The varnish is water-resistant, impact-resistant, and resistant to alcohol as well as mild chemicals. It is suitable for wooden surfaces indoors and outdoors above the waterline, especially for dimensionally stable woods such as marine plywood, solid wood, and wood veneer. It is particularly suitable as a satin gloss finish on EPIFANES POLY-URETHANE DD Yacht Varnish clear (Art.No. 2063-900), PP-VERNIS EXTRA Clear Varnish (Art.No. 2063-901), epoxy resins, and existing two-component satin varnishes.Application: Stir the components well and mix in a ratio of 2:1 (base:hardener) by weight and let stand for 15-30 minutes (induction time). If necessary, adjust to application viscosity with thinner. The varnish can be applied with a brush or spray gun. Application should be done at a minimum of 10 °C, with relative humidity not exceeding 75%. An intermediate sanding is not necessary if overcoated within 24 h. After 48 h, intermediate sanding with P360 is necessary. For optimal layer build-up, priming with EPIFANES PP VARNISH EXTRA is recommended.Technical DataApplication area: Satin-gloss 2-C clear varnish for indoor and outdoor areas above the waterlineSubstrate: Dimensionally stable wood (plywood, solid wood, veneer)Primer: EPIFANES PP VARNISH EXTRA recommended for base build-upCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinner: EPIFANES PU Brush Thinner, PU Spray ThinnerApplication method: Brush or spray gun (professional users)Drying times (at 20 °C, 65% rel. hum.): Dust dry: 2 hrs, tack-free: 4 hrs, sandable: 24 hrs, recoatable: 24 hrsFor more information on application, see the Technical Data Sheet under 'Downloads'.Safety notice: Contains isocyanates. may cause allergic reactions. 

Extremely hard, high-gloss 2-component clear coat with UV filter. EPIFANES POLYURETHANE CLEAR COAT is suitable for interior and exterior use above the waterline in fresh and saltwater environments. The varnish offers very good UV protection, is resistant to water, alcoholic beverages, and mild chemicals, and forms a particularly hard, impact-resistant surface with excellent adhesion to solid wood, plywood, and veneers. Due to its excellent flow properties, it is also suitable for high-gloss finishes with a brush. Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and left to stand for 30 minutes (induction time). Application is done with a brush or spray gun at temperatures from 10 °C and a maximum of 75% relative humidity. A “mist coat” is recommended for the first spray pass. Thinning with EPIFANES PU Brush Thinner (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310) is possible. An intermediate sanding is not required if the next coat is applied within 24 hours.Technical DataApplication area: High-gloss 2-C clear coat for wood in above-water areas Substrate: Solid wood, plywood, veneer – clean, dry, sandedPrimer: none, optionally EPIFANES Vernis Extra for fast layer buildupCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinning: EPIFANES PU Brush Thinner, PU Spray Thinner Application method: Brush or spray gun Drying times (at 20 °C): Dust-dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther processing information can be found in the Technical Data Sheet under 'Downloads'.Safety Note: Contains isocyanates. may cause allergic reactions. 

Extremely hard, high-gloss 2-component clear varnish with UV filter. EPIFANES POLY-URETHANE Yacht Varnish Karaat Mahogany has the same properties as EPIFANES POLY-URETHANE Clear Varnish (Art.No. 2063-900). Due to its mahogany-colored pigmentation, it is suitable for tinting existing varnish systems or for a reddish-pigmented new build on bare wood. Suitable for interior and exterior use above the waterline in fresh and saltwater environments. The varnish offers very good UV protection, is resistant to water, alcoholic beverages, and mild chemicals, and forms an especially hard, impact-resistant surface with excellent adhesion to solid wood, plywood, and veneers. Due to its excellent flow properties, it is also suitable for high-gloss finishes with a brush.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and left to stand for 30 minutes (induction time). Application is done with a brush or spray gun at temperatures from 10 °C and a maximum of 75% relative humidity. A "mist coat" is recommended for the first spray application. Dilution with EPIFANES PU Brush Thinner (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310) is possible. An intermediate sanding is not required if the next coat is applied within 24 hours.Technical DataApplication area: High-gloss 2-component clear varnish for wood above the waterlineSubstrate: Solid wood, plywood, veneer – clean, dry, sandedPrimer: none, optionally EPIFANES Vernis Extra for quick build-upCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinning: EPIFANES PU Brush Thinner, PU Spray ThinnerApplication method: Brush or spray gunDrying times (at 20 °C): Dust-dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions.

EPIFANES PP Varnish EXTRA is a fast-drying, two-component clear varnish based on alkyd resin and isocyanate with a high solids content and excellent chemical and mechanical resistance. The high-gloss varnish is suitable for interior and exterior use above the waterline and can also be used as a sealer on oily woods such as teak, iroko, or Oregon pine. It forms an elastic, filling protective film with high impact resistance, good gloss retention, and excellent adhesion to solid wood, veneer, and plywood. For optimal UV protection, a finishing coat is recommended.Application: The substrate should be sanded, dust- and grease-free, with a maximum wood moisture content of 15%. Mix both components at a 1:1 volume ratio and apply with a brush or spray gun after a 15-minute induction time. The first coat can be thinned with 5–10% EPIFANES THINNER FOR 2-C VARNISH PP. For exterior use, at least four coats are required. For optimal UV protection, a final topcoat with a 1-C varnish such as EPIFANES Clear Varnish (Art.No. 2050-001) or a 2-C PU varnish such as EPIFANES DD Varnish (2063-900) is recommended.Technical DataApplication area: 2-C clear varnish for wood above the waterline, interior and exteriorSubstrate: solid wood and plywood, suitable for teak, iroko, Oregon pinePrimer: Not requiredCoverage: approx. 14 m²/l at 30 µm dry film thicknessThinning: EPIFANES Thinner for PP Varnish Extra (Art.No. 2059-501)Mixing ratio: 1:1 by volumeApplication method: Brush or spray gun (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable: 20 hrs, recoatable wet-on-wet: 5 hrs (brush), 2.5 hrs (spray gun)Further information on application can be found in the Technical Data Sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions. 

EPIFANES RAPIDCLEAR is a fast-drying, satin gloss clear varnish based on urethane/alkyd resin with integrated UV filter. The varnish forms a transparent, amber-colored protective film that preserves the natural appearance of the wood grain. RAPIDCLEAR is suitable for interior and exterior applications above the waterline – especially for oily woods such as teak – and can also be used as a quick base coat before high-gloss systems like EPIFANES Yacht Varnish (Art.No. 2050-001) or Hardwood Varnish Oil (Art.No. 2051-050).Application: The surface must be clean, dry, grease-free, and sanded (max. wood moisture: 15%). Application is done with a brush or spray gun at temperatures between 12 °C and 28 °C. No sanding is required between coats if recoated within 72 hours. For a high-gloss finish, EPIFANES YACHT VARNISH CLEAR can be applied to the sanded surface. Technical DataArea of application: UV-resistant clear varnish for wood above the waterline, interior and exteriorSubstrate: Clean, dry, sanded, max. 15% wood moisturePrimer: Not requiredCoverage: approx. 13 m²/l at 30 µm dry film thicknessThinner: Epifanes Paint Thinner (brush), Epifanes 1K Spray Thinner (spray gun)Application method: Brush or spray gun (not airless)Drying times (at 20 °C): Dust dry: 1 h, sandable: 2 h, recoatable: 5–8 hDurability: For long-lasting UV protection, at least 5–6 coats recommendedFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Quick-drying, teak-tinted, semi-matt clear varnish with integrated UV filter for all types of wood above the waterline. The varnish combines easy application with good flow and even coloration - even on oily woods such as teak. EPIFANES RAPIDCOAT can be used both indoors and outdoors and is suitable as the sole protective coating or as a base for EPIFANES RAPIDCLEAR (Art.No. 2051-075), boat varnish (Art.No. 2050-001) or WOODFINISH GLOSS/MATTE (Art.No. 2051-001/2051-002).Application: The surface must be dry, clean and degreased. Apply with a soft brush or by spraying at 8-30 °C. Stir the container well and apply 5-6 coats. For a high-gloss finish, finish with RAPIDCLEAR or a high-gloss lacquer. Intermediate sanding is not necessary within 72 h. If the interval is exceeded, sand the surface lightly (P280-320).Technical dataArea of application: Pigmented wood protection for interior and exterior areas above the waterlineSubstrate: All common types of wood, incl. teak

EPIFANES RUBBED EFFECT VARNISH is a fast-drying, scratch-resistant 1-component clear varnish based on urethane/alkyd resin with a satin finish. The varnish is suitable exclusively for interior areas and creates a warm, silky surface with good resistance to alcohol and common household cleaners. Application: On bare wood, it is recommended to first build up with several coats of high-gloss varnish such as EPIFANES CLEAR VARNISH (Art.No. 2050-001). Then, apply two coats of EPIFANES RUBBED EFFECT VARNISH. Best results are achieved with a soft long-hair brush. Alternatively, spray application is also possible. Wet sanding between coats with P400 is recommended. Technical DataApplication area: Satin finish topcoat for interior surfacesSubstrate: existing paint systems; clean, dry, sandedPrimer: High-gloss clear varnish (e.g. EPIFANES CLEAR VARNISH) recommended as base build-upCoverage: approx. 15 m²/l at 30 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001), EPIFANES SPRAY THINNER (Art.No. 2059-110)Application method: Brush, spray equipment (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable: 12 hrs, recoatable: 12 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

HEMPEL'S CLASSIC VARNISH is a traditional, transparent clear varnish based on alkyd resin and tung oil (chinese wood oil). It forms a flexible and weather-resistant high-gloss film with good resistance to seawater, UV radiation, and fluctuating weather conditions. The varnish is suitable for new and renovation coatings on wood surfaces indoors and outdoors above the waterline.Application On new untreated wood, a priming coat with HEMPEL'S WOOD IMPREG (Art.No 2577-016) is recommended. This is followed by two thinned coats with HEMPEL'S THINNER 811 (Art.No 2577-900) (first coat max. 20%, second max. 10%), then three unthinned coats. Sanding between coats is recommended. For maintaining existing varnished surfaces, a light sanding is recommendede followed by three unthinned coats. Technical DataField of application: Clear varnish for wood surfaces above the waterline (indoor and outdoor)Substrate: Dry, clean, grease-free, sanded; max. 16% wood moisturePrimer: HEMPEL'S WOOD IMPREG (Art.No 2577-016) recommended for new woodCoverage: approx. 17 m²/l at 30 µm dry film thicknessThinner: HEMPEL'S THINNER 811 (Art.No 2577-900), max. 20%Application method: Brush, varnish pad, spraying (professional use)Drying times (at 20 °C): Touch dry: 6 hrs, sandable: 24 hrs, recoatable: 8–48 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

HEMPEL'S DURA-GLOSS VARNISH is a fast-drying, high-gloss clear varnish with a balanced ratio of hardness and flexibility. The formulation with optimized UV filters offers long-lasting protection and a professional appearance. The varnish is resistant to abrasion and wear and is suitable for new and maintenance coatings on wooden surfaces indoors and outdoors above the waterline.Application: For untreated wood, a primer with HEMPEL'S WOOD IMPREG (Item No. 2577-016) is recommended as a first coat. This is followed by two thinned coats of DURA-GLOSS VARNISH (first coat max. 20%, second max. 10% thinned with HEMPEL'S THINNER 811 (Item No. 2577-900)), then three unthinned coats. Sanding between coats is recommended. For maintaining existing coatings, sand an clean the surface and apply three unthinned coats.Technical DataApplication area: High-gloss clear varnish for wood indoors and outdoors above the waterlineSubstrate: Dry, clean, grease-free, max. 16% wood moisturePrimer: HEMPEL'S WOOD IMPREG for untreated woodCoverage: approx. 19 m²/l at 25 µm dry film thicknessThinner: HEMPEL'S THINNER 811Application method: Brush, varnish pad, spraying (professional users)Drying times (at 20 °C): Touch dry: 3 hrs, sandable: 24 hrs, recoatable: 4–48 hrs (depending on number of coats and temperature)Further information on application can be found in the Technical Data Sheet under 'Downloads'.

HEMPEL'S FAVOURITE VARNISH is a transparent high-gloss varnish based on urethane alkyd resin. It is easy to apply, flexible, and weather-resistant, with good protection against sunlight, seawater, and changing climatic conditions. Suitable for new and maintenance coatings on wooden surfaces indoors and outdoors above the waterline.Application: For new, untreated wooden surfaces, a pre-treatment with HEMPEL'S WOOD IMPREG (Item No. 2577-016) is recommended. The first coat of varnish is thinned with max. 20% HEMPEL'S THINNER 811 (Item No. 2577-026), the second with max. 10%. This is followed by three unthinned coats. An intermediate sanding is recommended between coats. For already coated surfaces, three unthinned coats are applied on well sanded old coatings.Technical DataField of application: High-gloss varnish for wooden surfaces above the waterline (indoor and outdoor)Substrate: Clean, dry, sanded, grease-free; max. 16% wood moisturePrimer: HEMPEL'S WOOD IMPREG Coverage: approx. 16 m²/l at 30 µm dry film thicknessThinning: HEMPEL'S THINNER 811Application method: Brush, roller, spray application (professional users)Drying times (at 20 °C): Touch dry: 4 hrs, sandable: 24 hrs, recoatable: 6–48 hrsFurther information on application can be found in the technical datasheet under 'Downloads'.

High-gloss, fast-drying polyurethane clear coat with an especially hard surface and very good weather and UV resistance. The amber-colored varnish enhances the natural wood grain and is suitable for all common types of wood in outdoor areas above the waterline. INTERNATIONAL COMPASS clear varnish is resistant to oil, mild acids, alkalis, and alcohol splashes and can also be applied directly to oily woods such as teak or iroko.Application: The surface must be clean, dry, and free of grease. For raw wood, the first coat should be applied thinned, followed by 3–5 unthinned coats with sanding between every 2nd to 3rd coat (P320–400). For oily woods, pretreatment with INTERNATIONAL Thinner No. 1 (Art.No. 2550-006) is recommended. Application is done with a brush, roller, or spray device at temperatures between 5 °C and 35 °C. Technical DataArea of application: High-gloss clear coat for outdoor areas above the waterlineSurface: Clean, dry, sanded, max. 18% wood moisture; also suitable for teak and irokoPrimer: none, thin the first coatCoverage: approx. 14.3 m²/l (theoretical)Thinner: Brush: Thinner No. 1 , Spraying: Thinner 910 or 920Application method: Brush, foam roller, or professional spray deviceDrying times (at 15 °C): Dust dry: 45 min, recoat: after 8 hrs.For further information on application, please refer to the Technical Data Sheet under 'Downloads'.

INTERNATIONAL ORIGINAL is a traditional, high-gloss clear varnish based on wood oil with excellent UV protection. The product is suitable for all common types of wood above the waterline and impresses with good flexibility, long-lasting gloss retention, and a clear, warm appearance – especially on light woods. The varnish is water-resistant, non-chalking, and suitable for both interior and exterior use.Application: The surface must be dry, free of grease, and sanded (bare wood: P80–180, old coatings: P280–320). Stir well before use. The first coat should be thinned with 10–15% INTERNATIONAL Thinner No. 1 (Art.No. 2550-006). Then apply at least three undiluted coats. An intermediate sanding with P320–400 is recommended between coats. Application is done with a brush, roller, or spray device at temperatures from 10–35 °C.Technical DataArea of application: High-gloss clear varnish for wood above the waterline (interior and exterior)Substrate: All types of wood with appropriate preparation, max. 18% wood moisturePrimer: noneCoverage: approx. 12.5 m²/l (theoretical)Thinner: Brush: Thinner No. 1, Spraying: Thinner 910 or 920Application method: Brush, roller, conventional spraying, airless or airmix (professionals only)Drying times (at 15 °C): Dust dry: 10 hrs, recoatable: 24 hrs to 4 daysFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

Traditional, high-gloss clear varnish based on wood oil with excellent UV protection. INTERNATIONAL SCHOONER is suitable for interior and exterior areas above the waterline and can also be applied directly to oily woods such as teak and iroko. SCHOONER offers excellent water resistance, good flow properties, and a warm, golden tone.Application: On bare wood, the first coat is applied thinned with 10% INTERNATIONAL Thinner No. 1 (2550-006). This is followed by 4–6 unthinned coats with intermediate sanding (grit P320–P400). Previously varnished surfaces are cleaned with Super Cleaner, sanded, and refinished with 2–4 coats. Application is done with a brush, roller, or spray equipment at 10–29 °C. Good ventilation and a dry environment are required for drying.Technical DataApplication area: High-gloss clear varnish for wood in above-water areas, interior and exteriorSubstrate: Wood, especially oily woods such as teak and iroko Primer: Not required; priming through 10% thinned first coatCoverage: approx. 14 m²/l (brush), approx. 12 m²/l (spraying)Thinner: Thinner No. 1 (brush), No. 1 or No. 910 (spraying)Application method: Brush, roller, conventional or airless spray application (professional use only)Drying times (at 15 °C): Dust dry: 2.5 hrs, recoatable: 14 hrs–1 monthFor more information on application, refer to the Technical Data Sheet under 'Downloads'.

LACQ YACHTLACK is a traditionally cooked clear varnish based on wood oil and phenolic resin with a high solids content and integrated UV filter. It forms a high-gloss, elastic protective layer with excellent weather and water resistance. The varnish is suitable for new builds on solid, raw wood (e.g. mahogany, meranti, Oregon pine) as well as for renovation coats on intact 1K or 2K varnish systems in the above-water area. Also suitable for doors, window frames, and garden furniture.Application: The varnish is applied with a brush or by spraying. For new builds, seven coats are recommended: the first coat diluted 50%, the second 25%, the third 15%, coats 4 to 7 only 0–5%. Intermediate sanding is done with P220 (dry), P280 (dry), and P400 (wet). Dilution is done with turpentine (brush) or petrol (spray gun). Technical DataApplication area: High-gloss clear varnish for wood surfaces in the above-water area Substrate: Solid wood (e.g. mahogany, meranti, Oregon pine), plywood; clean, dry, sandedPrimer: Not required Coverage: approx. 14 m²/l (depending on substrate and application)Thinning: Turpentine (brush), petrol (spraying)Application method: Brush or spray gun (1.2–1.5 mm nozzle, 2–3 bar, 20–24 sec. DIN 4)Drying times (at 18 °C): Dust dry: approx. 24 hrs, recoatable: approx. 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

LE TONKINOIS PARQUETS is an open-pore parquet varnish based on oil for wooden floors in indoor areas. The formulation with linseed oil, tung oil, and alkyd resins allows deep penetration into the wood capillaries, thereby reducing swelling and shrinking. The varnish offers long-lasting protection against abrasion and wear and is also UV-resistant. The natural wood grain is preserved and visually enhanced.Application: Wooden surfaces to be treated should be sanded, free of grease and dust. For soft woods, a prior primer coat with LE TONKINOIS Bio Impression is recommended. Stir well before use, do not dilute. LE TONKINOIS PARQUETS is applied in thin layers with a brush, roller, or floor varnish roller. Depending on the type of wood, apply at least two to three coats. Apply only one coat per day. Sand between layers with max 180 grit.Technical DataApplication area: Protective varnish for indoor wooden floorsSubstrate: Untreated wood, wood-based materialsPrimer: Bio Impression for soft woods (optional)Coverage: 20 m²/l per coat (depending on the absorbency of the wood)Application method: Brushing, rolling, sprayingDrying times (at 20 °C): Dust-dry after 6–8 h, re-coatable after 24 hFor more information on application, see the Technical Data Sheet under 'Downloads'.

A traditional clear varnish that is very elastic, penetrating and does not flake. Traditionally produced by gentle boiling of linseed and tung oil. In contrast to synthetic resin varnishes, RYLARD VG63 dries very slowly, which gives it the elasticity and durability required for solid wood boats. The varnish is particularly suitable for use on wood in the boating sector or in other heavily used environments.Application: On dry, clean wood, first apply two coats of RYLARD IMPREGNANTE (Art. No. 6080-701) to saturate the wood; alternatively, VG 63 diluted with turpentine substitute (mixing ratio 1:1) is also suitable.Depending on the absorbency of the wood, then apply five to six coats of VG 63 - each coat thinly and 24 hours apart. The first coat should be thinned to 30-40%, then gradually reduce the thinning. Apply the last two coats undiluted. Intermediate sanding with fine sandpaper is recommended. For painted surfaces in good condition, the surface should be thoroughly sanded, cleaned and degreased before applying two coats of VG 63. Do not apply in damp weather, below 15 °C or on wet wood.RYLARD varnishesWith its RYLARD brand, the Italian ship and yacht paint manufacturer BRAVA from Genoa offers a range of traditional yacht paints whose original formulation was developed for the early days of yachting in the 19th century and is known as "Yachtman's Mirror" on many classic yachts.Technical dataArea of application: Clear lacquer for wooden surfaces in the maritime sector and demanding environmentsSubstrate: Clean, dry, untreated or stripped woodPrimer: RYLARD IMPREGNANTE (optional)Coverage: 20 m²/lDilution: Turpentine substituteApplication method: Brushing or sprayingDrying times (at 20 °C): Dust-dry after 12 h, recoatable after 24 hFurther information on application can be found in the technical data sheet under 'Downloads'.

A transparent, high-gloss clear varnish based on modified oleophenolic (oil-compatible) resins with linseed oil and tung oil. It contains UV filters and is characterized by high elasticity, long-lasting gloss retention, and reliable protection against weather influences, sunlight, and temperature fluctuations. RYLARD VG 66 PREMIUM is particularly suitable for high-quality varnishing of wood on and on classic boats.Application: The surface must be clean, grease-free, and dry. On untreated or stripped wood, first apply two coats of diluted RYLARD VG 66 PREMIUM (1:1 with white spirit). Then apply four to six coats of undiluted varnish at intervals of at least 24 hours. A light intermediate sanding is recommended before the final coat.Technical DataApplication area: High-gloss protective varnish for wood in maritime outdoor areasSubstrate: Untreated or stripped, clean and dry woodPrimer: none, optional RYLARD VG 61Coverage: 18 m²/lThinner: white spiritApplication method: Brushing or spraying Drying times (at 20 °C): Dust dry after 8 h, reworkable after 24 hFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

SIGMA VARNISH YACHT GLOSS (formerly known as SIGMARINE 42) is a high-gloss, solvent-based clear varnish based on wood oil, phenolic and alkyd resin. The varnish has been specially developed for high-quality wood surfaces outdoors and is particularly suitable for yachts and boats above the waterline. It is weatherproof, resistant to salt and fresh water, offers very good elasticity and excellent surface flow quality. Application: Before painting, the wood must be clean, sanded and additionally degreased for oily woods. The maximum wood moisture content is 18%. For new coatings, an initial impregnation is recommended, followed by three coats of SIGMA VARNISH YACHT GLOSS. For renovation of existing coating structures, damaged areas are sanded down to bare wood, impregnated and rebuilt. Application is done with a brush, and can be thinned with a maximum of 2% SIGMA THINNER 20-05 if necessary.Technical DataArea of application: Clear varnish for wood outdoors above the waterline, e.g. on yachts and boatsSubstrate: Clean, sanded, dry, grease-free; max. 18% wood moisturePrimer: SIGMA WOODPROTECT 2IN1 CLASSIC SATIN CLEARCoverage: approx. 16.5 m²/l at 30 µm dry film thicknessThinning: Ready for use; max. 2% SIGMA THINNER 20-05 if neededApplication method: Brush (suitable for solvent-based varnishes)Drying times (at 23 °C, 50% rel. humidity): Dust-dry: 3–4 hrs, tack-free: 4–6 hrs, sandable and recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

VOSSCHEMIE G8 SUPER is a one-component polyurethane clear coat with high resistance to chemicals, cleaners, and weathering. The solvent-based coating cures through humidity, remains nearly non-yellowing, and is suitable for many absorbent substrates such as wood, metal, and solvent-resistant plastics. Due to its formulation, the product does not contain additional UV absorbers and is not suitable for use in living areas.Application: G8 SUPER is applied with a brush or spray gun. The substrate must be clean, dry, and free of grease; solid wood must not exceed a maximum wood moisture content of 15%. For priming on porous substrates, dilution with a maximum of 50% polyurethane thinner is recommended. The application amount per layer should not exceed 250 ml/m². For a durable surface film, at least three undiluted coats are required. Recoating can be done after 2–4 h or alternatively after intermediate sanding.Technical DataApplication area: Clear coat for wood, metal, plastics, and epoxy laminatesSubstrate: Clean, dry, grease-free; solid wood max. 15% wood moistureCoverage: approx. 200–300 ml/m² per coatThinning: Max. 50% polyurethane thinner recommended for primingApplication method: Brushing or sprayingDrying times (at 20 °C): Dust dry after 2–4 h, recoatable within 24 hCuring time: Fully cured after at least 7 daysNote: Product contains hazardous chemicals according to the REACH regulation. We recommend use only by professional users. Contains isocyanates. May cause allergic reactions. As of August 24, 2023, appropriate training must be completed before industrial or professional use (EU REACH regulation). Further information can be found in the technical or safety data sheet under 'Downloads'.