Small bilge pump WHALE SUPERSUB | TOPLICHT

To be able to use the full range of Shopware 6, we recommend activating Javascript in your browser.

Jobs

Catalogue

Art. No.	WHALE No	voltage (V)	current (A)	D1 (mm)	L (mm)	B (mm)	Price (unit)	Delivery time	Note list	Buy

Downloads

Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE,
which can also be placed between frames and floor boards.
Removable sieve, outflow hose adjustable from horizontal to vertical.

Article 1441-111 comes with a non-return valve.

Versions:
SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. ,
SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.

Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.

Questions about the product?

Accessories

Multiflex hose PVC

Multiflex hose PVC

Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).

From €4.90 *

Hose clamp stainless steel

Hose clamp stainless steel

Solid stainless steel design - all pieces completely stainless.With hexagonal bolts for high torque, high tear resistance and elasticity.

From €1.80 *

T-bolt clamp

Heavy, wide hose clamps, made entirely of A2-stainless steel.Hexagonal bolt for easy mounting in hard-to-reach corners. Due to the width particularly well suited for hose mounting on board.Type: HEAVY DUTY.

From €5.90 *

WHALE field sensor bilge switches BE9003 / BE9006

WHALE field sensor bilge switches BE9003 / BE9006

This electronic level switch does not require any mechanics or moving parts. Two field sensors ensure functional switching on and off of the connected pump. The switch turns on at 51 mm water level and turns off at 13 mm water level. The automatic sensor type BE9006 switches with an automatic 30 seconds switch-off delay. This delay allows water to be pumped out even below the switching level of 13 mm. The test function can be used to check the function of the pump after installation.Voltage: 12 V / 24 V.Max. switch current: 20 A.Residual current: 0,008 A.

From €69.00 *

Switch panel for bilge pump SEAWORLD

Switch panel for bilge pump SEAWORLD

Switch panel for automatic bilge pump. With sound and light alarm when pump is running automtically.With toggle switch, positions: "automatic/off/manual". With control lights and fuse 16 A/12 V. For 12 volt systems.

€25.90 *

Automatic Float Switch ATTWOD 4201

Automatic Float Switch ATTWOD 4201

Compact automatic switch for many installation possibilities, even on sloping surfaces with an angle of up to 24°. The switch works reliably and switches on as soon as the water in the bilge reaches a height of about 5 cm. The cover provides extra protection for the float switch, for example against dirt and coarse parts.Housing L x W x H: 133 x 98 x 73 mm. For: 12 - 24 V. Switching capacity: 120 VA max. 12 amps with 12 V.

€39.00 *

Similar products

Bilge pump RULE MATE

Bilge pump RULE MATE

The proven automatic bilge pump, from US manufacturer RULE.Plastic housing with easily removable sieve baseplate.Quiet and fully encapsulated motor, stainless axis.Can be used as an automatic pump:Type RULE-MATE (RM) is controlled with an integrated electronic switch. Supplied with straight hose nozzles for 25 and 28 mm.

From €129.00 *

Bilge pump WHALE ORCA

Bilge pump WHALE ORCA

Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.

From €39.90 *

Bilge pump MARCO

Bilge pump MARCO

High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.

From €37.95 *

Submergible bilge pump RULE

Submergible bilge pump RULE

Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.

From €35.90 *

Bilge pump RULE AUTOMATIC

Bilge pump RULE AUTOMATIC

The proven bilgepump from the US manufacturer RULE. Plastic housing with easily removable sieve baseplate. Quiet-running and fully encapsulated motor. Also made as an automatic pump: Type: RULE-AUTOMATIC (RA) works through an automatic microprocessor that checks if there is water in the bilge by briefly running the pump every 150 seconds (without a mechanical switch). Limited power requirements for the test runs: Only approx. 0.2-0.5 Ah per day.

From €135.00 *

RULE LO-PRO Submersible Bilge Pump LP900D / LP900S

RULE LO-PRO Submersible Bilge Pump LP900D / LP900S

Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.

From €69.00 *

Small bilge pump WHALE SUPERSUB-SMART

Small bilge pump WHALE SUPERSUB-SMART

Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.

From €94.90 *

Thru-hull hose fitting polished or chromed

Thru-hull hose fitting polished or chromed

Through-hull with attached hose nozzle. Made of brass (seawater resistant brass, depending on manufacturer CW602N - CuZn36Pb2AS or CW625N - CuZn35Pb1,5AlAs).Comes in rolled brass or with a chromed finish.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €11.00 *

Last seen products

More articles from this category

Bilge pump MARCO

Bilge pump MARCO

High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.

From €37.95 *

Submergible bilge pump RULE

Submergible bilge pump RULE

Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.

From €35.90 *

Bilge pump RULE MATE

Bilge pump RULE MATE

The proven automatic bilge pump, from US manufacturer RULE.Plastic housing with easily removable sieve baseplate.Quiet and fully encapsulated motor, stainless axis.Can be used as an automatic pump:Type RULE-MATE (RM) is controlled with an integrated electronic switch. Supplied with straight hose nozzles for 25 and 28 mm.

From €129.00 *

Bilge pump RULE AUTOMATIC

Bilge pump RULE AUTOMATIC

The proven bilgepump from the US manufacturer RULE. Plastic housing with easily removable sieve baseplate. Quiet-running and fully encapsulated motor. Also made as an automatic pump: Type: RULE-AUTOMATIC (RA) works through an automatic microprocessor that checks if there is water in the bilge by briefly running the pump every 150 seconds (without a mechanical switch). Limited power requirements for the test runs: Only approx. 0.2-0.5 Ah per day.

From €135.00 *

Bilge pump WHALE ORCA

Bilge pump WHALE ORCA

Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.

From €39.90 *

Electric diaphragm pump WHALE GULPER 220

Electric diaphragm pump WHALE GULPER 220

WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.

From €198.00 *

Electric diaphragm pump WHALE GULPER 320

Electric diaphragm pump WHALE GULPER 320

WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.

From €259.00 *

Small bilge pump WHALE SUPERSUB

Small bilge pump WHALE SUPERSUB

Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Removable sieve, outflow hose adjustable from horizontal to vertical.Article 1441-111 comes with a non-return valve. Versions:SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. , SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.

From €49.90 *

Small bilge pump WHALE SUPERSUB-SMART

Small bilge pump WHALE SUPERSUB-SMART

Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.

From €94.90 *

Impeller pump JABSCO UTILITY-PUPPY 2000

Impeller pump JABSCO UTILITY-PUPPY 2000

Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).

From €439.00 *

RULE LO-PRO Submersible Bilge Pump LP900D / LP900S

RULE LO-PRO Submersible Bilge Pump LP900D / LP900S

Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.

From €69.00 *

Bilge pump FLOJET QUAD 4125

Bilge pump FLOJET QUAD 4125

High-performance bilgepump without pressure switch, laid out as a four-chamber membrane pump.The pump is self-priming to 2 m, can run dry safely and runs extremely quietly, thanks to rubber mountings.Attachment: plug with 19 mm hose nozzle, plug with 3/4" male thread.We exclusively carry FLOJET pumps, which have been developed especially for the marine industry (not camping pumps).Comes with wide-mesh screen.

From €279.00 *

Grey water and bilge diaphragm pump JABSCO 50880

Grey water and bilge diaphragm pump JABSCO 50880

A new generation of diaphragm pump in the one compartment design by pump specialist JABSCO.Ideal for the draining of shallow bilges and shower drains.Maintanance is simplified by the filterless design and the pump is indeed free of clogging.Characteristics:Flow rate: Nominal 16 Litres/min. Self-priming from dry up to 3m (10ft) Flexible installation Dry running capability

From €209.90 *

RHEINSTROM deck wash and bilge pump type 4E

RHEINSTROM deck wash and bilge pump type 4E

This self-priming bilge and deck wash pump is suitable for delivering sea water. It is completely made of bronze and stainless steel. Due to its hard-wearing industrial motor a longlasting and reliable operation is guaranteed. Before it is run for the first time it has to be filled with water. Furthermore it is advisable to install a socket safety valve or a foot operated valve into the suction pipe. The pump is non-reactive to sand (particle size up to 2 mm). The model 4 E is totally maintenance-free due to the use of a freely running impeller wheel and a very modern axial face seal. The max. operating time is 1 – 2 hoursTechnical dataOutput:50 l/minHeight pumped: 13 mSuction lift: 3 mAttachment: 3/4" BSP with inner threadsWeight: 7 kg

From €916.00 *

RHEINSTROM diaphragm pump M50E

RHEINSTROM diaphragm pump M50E

Very powerful, self-priming electrical diaphragm pump with reliable industrial motor.This Rheinstrom diaphragm pump has been found to be very reliable over many years. It can be used as a bilge pump, a grey water pump and a delivery pump.Constant delivery rate, high safety against clogging, very good cleaning possibilities.Made of hard-wearing materials, the body is made of seawater-proof cast bronze.Fast and easy cleaning and maintenance and direct access to the valves are obtained by simply opening the lid of the pump. The discharge and suction side may be altered.Technical dataPump performance: 40 l/minDelivery head: 10 mSuction height: 3,5 mConnection: 38 mm hose connectionMotor: 110 WWeight: 9,5 kgA repair kit is available.

From €990.00 *

Request sent successfully

Request wasn't send - a error occured. Please try again.