Different types of antenna sockets. All sockets are suitable for VHF or GPS antennas or active radar target enhancer with standard theads 1" x 14 TPI. Available versions:GLOMEX long, stainless steelstandard long, stainless steelstandard short, stainless steelstandard short, white plastic (PA)
Practical wind indicator for the VHF antenna, suitable for all 2,5mm stainless steel rod antennae.Easy to mount, with adjustable angular arms, 380 mm pointer length.Delivery without VHF antenna.
Light high-performance, stainless steel VHF whip antenna, ideal for mast mounting on sailboats.Gain 3 dB.Length 100 cm, weight only 360 g.PL socket for cord attachment.Comes complete with 18,0m VHF cable RG58U, complete with mounting screw on antenna side and one straight PL259 plug.
Fiberglass VHF rod antenna CX, 156-163MHz. 3 dB gain.Length overall 130 cm, antenna 120 cm, weight 0.5 kg.With chromed union nut 1"BSP and PL-socket.For mounting with a standard deck or rail fitting with 1"x14TPI threads an additional adaptor Art-Nr. 3940-102 is required (which is not supplied with the antenna).
Adapter tube made of A4 stainless steel, for mounting a CX antenna (with union nut 1" BSP) on an antenna base with thread 1" x 14TPI.Adapter threads:matching 1" BSP male thread on one side for the union nut of the CX antenna,one side female thread 1" x 14TPI, suitable for antenna bases with 1" x 14TPI male thread.The tube has a long slot on the side through which the antenna cable can be routed to the outside.
Stainless steel adapter to fit a CX antenna to a standard tube with outer diam. 26mm.One side with 1" BSP outer thread for the union nut f the antenna, opposite side to a tube with outer diameter 26mm.Hex socket screws to fix the adapter to the tube.The cable may go through the fitting into the tube..
Antenna mounts made from stainless steel for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.
Rotatable antenna mounts made from white polyamide (PA) for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.
These small diplexers allow the simultaneous use of a VHF radio, a FM/AM radio and an AIS device, using only a single antenna.Output max. 30W/channel, for frequencies 156-162 Mhz, 163 Mhz (AIS), 0,5-108 Mhz. Available are two versions: VHF / AIS / AM/FM:Active crossover switch, with output for VHF telephone, VHF/AM/FM radio, AIS receiver (only for receiving AIS informations, not for transmitting) Switch is wired for VHF telephone and AIS receiver with 50 cm of cable and matching PL plugs. Radio-out: F socket for F plug. Antenna-in: PL socket.Operating voltage: 12-24 V, current 0,04 Amps. Plastic housing. VHF / AIS transponder / AM/FM: Active crossover switch, with output for VHF, AM/FM radio, AIS transponder (receiving and transmitting of AIS informations). Completely wired for VHF and AIS with 100 cm cable and matching PL plugs.Operating voltage: 10-30 V, current 0,1 Amps. Metal housing.
With this isolator backstays and shrouds can be made into effective radio antennas. The isolator must be installed in two intertwined wire eyes. The cleanly milled grooves thereby allow the wires a large bending radius, through which they are able to retain their strength.Made from the saltwater-resistant plastic Polyacetal (POM).
Isolator for installation on antenna wires or stays which are used for antennas. Lloyd Register qualified.Skilled processing means the breaking load of the appropriate wires is not reduced.Approved Norseman terminals on both sides.
Antenna mounts made from white polyamide (PA) for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.
Rotatable antenna mounts made from stainless steel for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.
Masthead bracket GLOMEX V9173 from stainless steel - mast mount with standard thread 1" x convolution 14 standard thread (1" x 14TPI).Can be installed on sailingboats & motorboats.Weight: 330g.
Short fibre glass antenna for VHF receivers 156-163 MHz.For a fixed installation.Comes complete with 18,0 m coax cable, RG58 plug and mounting bracket from stainless steel.Length of antenna 230 mm.
Fibreglass antenna with practical mounting bracket, which can be used to continue operating the radio system on superstructures or stationary equipment in an emergency (after mast breakage or similar damage), for example.Permanently mounted cable (4.5 m long) with PL plug, which can be quickly connected to any stationary radio device.Supplied with cable in practical plastic bag.Antenna length 240 mm.
Ground plates made from special porous material from bronze, with as large a surface as possible, are especially well suited for VHF radios.They improve the reception and range. They proved their worth with GPS units, weather decoders, weather fax receiver, as well as ham and shortwave radios.The plates are fixed with bolts to the hull and connected to the apparatus via cable.Shipping with screws and nuts from bronze.
